U can add a 2nd unit on ur guitar signal, in addition to one in ur loop to clean up any hum of interference ur guitar is picking up, but the threshold should be set low, just enough to eliminate unwanted noise but not chop up ur guitar signal. And Boss’s proprietary technology means the NS-2 works perfectly without affecting your core guitar tone. U definately want to run any noise reduction unit in the fx loop to clean up amp noise, which is ur goal with the 5150. The Boss NS-2 Noise Suppressor is the perfect pedal if you’re looking to quieten down a noisy set-up.If youre tired of annoying noise and hum, the NS-2 is the answer and features Boss unique noise detection circuit. It sounds like at the threshold u indicated, u would be minimizing your guitar signal therefore minimizing tone. All it's doing there is reducing noise in your guitar signal, it's not affecting the amp noise at all.
Parallel DC Cord: PCS-20A Size and Weight Width 73 mmĢ-3/8 inches Weight (including battery) 415 gġ5 oz * 0 dBu = 0.775 Vrms * The specifications are subject to change without notice.Second, I would definately run it in your fx loop, not between ur guitar and amp input.
Ns2 boss series#
Leaflet ("USING THE UNIT SAFELY," "IMPORTANT NOTES," and "Information")Ĭarbon-zinc battery (9 V, 6F22) Options (sold separately) AC adaptor: PSA series UPDATE: 4,7uF C25 10uF to 1uF, to make the effect tone equal to the bypass mode.
Ns2 boss mods#
*These figures will vary depending on the actual conditions of use. Forging the Future - Innovation for Creative Inspiration BOSS forges into 2008 with an awe-inspiring lineup of effects, digital studios, and accessories. Boss Noise Supressor NS-2 or Behringer NR300 mods Mods for a more transparent bypass and effect, reducing the tone difference when the pedal is activated: C3 (output cap) 1uF to 10 uF, for better bypass tone. I didn't want to unmount mine from the pedalboard so did a Google image search and found these: Guitar > Boss NS2 Noise Suppressor > NS2 Send > MXR Custom Comp > Neo-Classic 741 Overdrive > NS2 Return/Output > VHT Special 6 Ultra Amp Input > Amp Send > MXR Carbon Copy Analog Delay > Boss RC3 Loop Station > Amp Return. The NS-2 can also be wired like an effects loop, which allows you to kill your entire signal chain just. Wire the Output jack of the NS-2 to your amp. The output of the previous pedal goes to the NS-2 input jack. You can connect the NS-2 last in your chain of effects. REDUCTION indicator Connectors INPUT jack: 1/4-inch phone typeĩV DC OUT jack Power Supply Carbon-zinc battery (9 V, 6F22) or Alkaline battery (9 V, 6LR61)ĪC adaptor (PSA series: sold separately) Current Draw 25 mA Expected battery life under continuous use Carbon: Approx. The NS-2 can be connected in two different ways. Pedal switch Indicator CHECK indicator (Serves also as battery check indicator) Sold by rimmersmusiclimited ( 15343) 98.8 positive Feedback Contact seller. The NS2 gates out this noise without adversely affecting your instruments tone. Natural attack and envelope remain unaffected by suppression of the noise components. Boss NS2 Noise Suppression Guitar Effects Pedal. The Boss NS-2 Noise Suppressor Pedal effectively eliminates noise and hum from the input signal while preserving the original sound's tonality. Nominal Input Level -20 dBu Input Impedance 1 M ohm Nominal Output Level -20 dBu Output Impedance 1 k ohm Recommended Load Impedance 10 k ohms or greater Bypass Buffered bypass Controls MODE selector switch The NS-2 from Boss allows you to eliminate unwanted noise and hum without altering your tone.
0 kommentar(er)
